How to find water for wells: dismantle three effective ways to search
Water is an exceptional gift, without which life on earth is simply impossible. Water is a permanent element of the daily cycle: watering plants, household needs, cooking… Acquiring land on which there is the slightest hint of the source of this inorganic compounds the problem of how to find water for a well or wells, is becoming one of the key. We offer you to disassemble the most popular and effective ways.
The contents
A little about aquifers
In the soil, usually within 2-3 aquifer, separated by confining layers, the horizons of which can vary greatly.
Aquifers represent a kind of underground lake, mainly consisting of water-soaked sand
At a least depth of about 25 meters is the water in the first layer, referred to as «subcutaneous» or perched. It is formed by filtration through the soil melt water and atmospheric precipitation. This water is only suitable as watering gardens and for household needs.
Water the second layer of mainland sand is suitable for human consumption. The third layer represent water with excellent taste, and rich in mineral compounds and mineral salts.
Effective ways of finding water
Ways to determine the proximity of water to the surface, there are more than a dozen. Search water bore can be carried out using one of the following effective ways.
Using silica gel
For this purpose granules of the substance had previously been thoroughly dried in the sun or in the oven and put in unglazed clay pot. To determine the number of granules absorbed moisture pot before burying you must weigh. A pot of silica gel wrapped in non-woven material or a thick cloth, burrows into the soil to a depth of about one meter in place at the site where it is planned to drill the well. After one day, the pot contents can be removed and again weighed: the heavier it is, the more moisture it has absorbed, which in turn indicates the presence of a nearby aquifer.
The use of silica gel are related to the category of substances having the property to absorb moisture and hold it, will allow only a couple of days to determine the best location for the drilling of wells or construction of well
In order to narrow the search space of water to wells, it is possible to use simultaneously several of these clay jars. To determine more precisely the optimal place for drilling by re-instillation of a pot of silica gel.
Moisture-absorbing properties has also the usual brick from red clay and salt. The definition of an aquifer occurs similarly to pre-and re-weighing and vyschityvanii difference.
Barometric method
Readings of 0.1 mm of mercury of the barometer corresponds to the difference in elevation of the pressure in 1 meter. To operate the appliance you must first measure its pressure on the Bank of an existing pond nearby, and after along the device to move to the site of the proposed arrangement of source water extraction. In place of drilling measurements of air pressure are made again and calculated the depth of the water.
The presence and depth of groundwater has also successfully determined using a conventional barometer aneroid
For example: the reading of the barometer on the banks of the river are 545,5 mm, and the area — 545,1 mm. the Level of groundwater is calculated according to the principle: 545,5-545,1=0.4 mm, i.e. the depth of the well would be less than 4 meters.
Exploration drilling
A trial exploration drilling is one of the most reliable ways to find water for wells.
Exploration drilling allows us not only to identify the presence and level of occurrence of water, but also to determine the characteristics of the soil layers, occurring before and after the aquifer
Drilling is done with the use of common garden hand drill. Since the depth of the prospecting wells in an average of 6-10 meters, it is necessary to provide the possibility to increase the length of the handle. For work, it is sufficient to use a drill, a screw diameter of which is 30cm. As penetration of the drill in order not to break the tool excavation must be carried out through every 10-15 cm soil layer. Moist silver sand can be seen at a depth of about 2-3 meters.
An illustrative example of test drilling are presented in the video:
Place under the arrangement of the well shall be located not closer than 25-30 meters with respect to the drainage of trenches, compost and garbage heaps, and other sources of pollution. The successful placement of the well is on an elevated plot.
Repeating terrain aquifers in the high places are the source of more pure filtered water
Perched rainwater and melt water always flows down from the hills to the lowland, which gradually drains to impermeable layer, which in turn displaces clean filtered water up to the level of the aquifer.