The contents
The frames are distinguished: production material – wood, plastic, or MLF, by type of coating is laminated or top coated with coatings (paint), veneer. The main goal is to hide the space between the door frame and the wall. Installation of trim on interior doors is performed on the last stage of the installation deri or General repair.
Contents:
- Installation of trim on interior doors: how to attach them
- Variants of installation of trim on interior doors
- Proper installation of trim on interior doors with their hands
- Requirements for the installation of trim on interior doors own hands
- Summarize
Installation of trim on interior doors than to attach them ↑
Most often, the frames are attached to the wall with finishing nails. It is recommended to choose the length not more 4 cm, because they have to fit in the canvas of the door frame at a distance not less than 1.5 cm.
This is the way simple and reliable. If necessary, they can always be dismantled and installed again.
The use of liquid nails for the fastening it is advisable to use in cases where both surfaces (box and wall) is perfectly flat.Working with them is very easy and convenient.
The reverse side of the clypeus covered with a thin layer of the adhesive composition, tightly against the wall and kept some time in a real state (a few seconds will be enough).
Liquid nails compared to regular, do not leave marks on the front of the plane. Work is done quickly, but as far as reliability, they are significantly inferior to traditional. Another disadvantage of this method of mounting complexity in the subsequent disassembly (if it will run). It is not recommended to use them and cases where obnalichniki set of wood.
Self-tapping screws. To install nalichnymi screws, they should choose the diameter 6 cm, length 3 cm.
To hide («drown») the cap screw on the face rassverlivajut small depression.
Attach them with the help of spectropia – «beaks». That is, obnalichniki wedged into special grooves in the doorframe. This method is the most aesthetic of all the. It is desirable to use such a method, elenaniki of MDF material.Because, if necessary, to dismantle it, «beak» may simply delaminate.
What are the options for the installation of trim on interior doors ↑
There are a few well-known options to set obnalichniki:
- Butt;
- With a decorative insert;
- Circumcised on the 450.
Butt. This installation option is alicyclobacillus rarely and then only in the case when mounted telescopic obnalichniki, because they are equipped with ledges that allows you to attach them to the transoms, door frame or, when the wall is significantly thicker box.
A decorative insert (drive). It is essentially 2 in 1: as part of the decor door and the jamb in one piece. Installation of insert is performed by butt. The drive can be used only in certain styles. Manufactured strictly under the order or in some models the doors can go in the kit.
Shirokolistnyj variant of the frame of the doorway – Montalbano, obrezanova angle of 450. If you want to install the moulding with his own hands from the material that you like, it is very easy to do. Only need to make accurate measurements, supporting the bar to the doorway and trim the edges.
Given the requirement that the height should not be the same with the inner part of the door frame, to calculate razorplate the width of the casing.After that, the bar-the workpiece is placed on the surface.Using the square determined the correct angle and trimmed.
Profilesegments architraves to interior doors with their hands ↑
Frames are alternately applied to the door opening, attached with nails.The distance between them should be about 50 cm and There is another variant of the fastening – nails are nailed directly into the box.The surface must remain at about 5 cm from the entire length is necessary in order to then «plant» on them frames. Hats on the nails resultsamerican.
After the installation, it is applied to the top placket, measure the length and trimmed on both sides. The fasteners of the upper strap casing is carried out similarly to the side.Resulting cracks are masked acrylic sealant or you can use a waxy concealer, it matched the color of the slopes.
Requirements for the installation of trim on interior doors own hands ↑
Of the basic rules of the installation work note the following:
- installation of platbands to nevozmojnosti,not aligning the walls of the opening with plaster. Just to disguise the cracks such methods is inadmissible;
- before mounting be sure to check the fit, in case of detection of any irregularities – dents or bulges.They necessarily eliminate.Otherwise, the design will be uneven (in this case, no nails can not do it tightly and firmly hold);
- if you are installing the trim on the input openings, the box should be saponite foam, because the drafts and the humidity is not the best way affect the design and the door in General;
- if the installation of the frames is performed on the interior openings, volatile mixture can not be applied. Only permitted chemicals, fire barriers;
- care trim needs to be regular, with a properly chosen detergents.
The link to the video:
Summarize ↑
Replayability is a simple process, so do all of the installation steps, even a novice master, however, only need patience.
All step-by-step recommendations must be strictly performed, otherwise you risk to receive instead of quality work – a bunch of spoiled nerves and building material.
