• 13/06/2022
• Categories: Coating materials

Bitumen mastic TekhnoNikol, specifications

Company TechnoNICOL, known on the market since 1992, is one of the leading manufacturers of hydro-, sound – and thermal insulation materials. The company cooperates with design institutes and responsive to the wishes of consumers.

Bitumen mastic — insulating material used in construction for different purposes.

Product range:

• Roofing mastic TekhnoNikol №21;
• waterproofing TECHNONICOL №24;
• emulsion TechnoNIKOL №33;
• adhesive TECHNONICOL 27;
• bitumen rubber No. 20.

Numerical designation of the postmark shows the degree of resistance to temperatures.

Mastic bitumen TechnoNIKOL №21 ↑

Material based on oil bitumen containing mineral additives and an organic solvent. This paste gives a high elasticity, adhesion, thermo – and moisture resistance.

The purpose of the material ↑

• waterproofing all types of roofs as waterproofing, and combined with the rolled insulation;
• waterproofing reinforcing structures exposed to moisture — foundations, piles, basement.
• anticorrosion treatment of metal structures;

The flow of mastic ↑

• the device mastic roofing — 3,8-5,7 kg/m^Two;
• for waterproofing — 2,5-3,5 kg/m^Two;

Specifications ↑

1. adhesion:
2. concrete — 0.6 MPa;
3. with metal — 0.9 MPa;
4. adhesion strength:
5. between the layers of rolled materials — 0.3 MPa;
6. roll material with a concrete — 0.4 MPa
7. strength displacement bonding — 4 kN/m;
8. conventional strength — 1 MPa;
9. stretch at break 500 %;
10. the absorption of water in the first 24 hours — 0,4 %;
11. non-volatile content to 50%.
12. maximum allowable temperature — 110° C;
13. good flexibility at the corners a radius of curvature of 5 mm, in a temperature of -35° C does not crack;
14. do not pass water during the first 24 h at a pressure of 0.1 MPa;
15. the temperature of the work — from -20 to +40° C for operation at temperatures below +5° C pre-soak in warm a minimum of 24 h;
16. curing time under normal conditions up to 24 hours;

Recommendations for use and storage ↑

The material is applied on a dry clean surface by brush, trowel or filling, spread the rule. For use in the cold mastic is pre-heated.

Do not use near open flame, avoid contact with skin and eyes. Store in a dry closed from sun light place at the temperature from -20 to +40° C. shelf Life — 18 months.

Waterproofing mastic TekhnoNikol 24 ↑

Mastic cold bitumen waterproofing with mineral fillers and solvent.

The purpose ↑

• obmazochnoy waterproofing of concrete, wood and other structures;
• protection of metal structures against corrosion

Specifications ↑

1. consumption per one layer — 1 kg/m^Two;
2. adhesion to concrete and metal — 0.1 MPa;
3. resistance to displacement of the bonding — 2,0 kN/m;
4. water absorption within 24 h of 0.4 %;
5. non-volatile content of 65 %;
6. heat resistance — 80° C;
7. viscosity — 10;
8. no cracks on the corner of a radius of curvature of 5 mm at a temperature of -5° C;
9. drying time under normal conditions up to 24 hours;
10. don’t pass water for 10 min at a pressure of 0.03 MPa;
11. the temperature of the work — from -20 to +40° C;

Recommendations for use and storage ↑

For operation at temperatures below +5° C to withstand warm a minimum of 24 h do Not use near open fire, bad ventilation, avoid contact with eyes and skin. Store in a dry closed from sun light place at the temperature from -20 to +30° C. shelf Life — 18 months.

Mastic emulsion TECHNONICOL 33 ↑

Water-based bituminous product, modified latex and polymer additives, without organic solvents.

The purpose ↑

• installation of mastic roofs;
• waterproofing deepen in the ground or in contact with moisture structures;
• internal waterproofing of the premises.

Specifications ↑

1. adhesion to concrete — 0.6 MPa;
2. conventional strength — 0,7 MPa;
3. the relative stretch at break of 900 %;
4. water absorption in tech. 24 p — 0.4 %;
5. the proportion by mass of the binder substance with the emulsifier — 53-65 %;
6. maximum withstanding temperature in tech. 5 hours — 140° C;
7. no cracks when bending on the corners rounding radius of 5 mm at -25° C;
8. waterproof in tech. 24 h under a pressure of 0.1 MPa;
9. curing time — 24 to 72 hours;
10. maximum durability — 3-7 days.

Method of application ↑

• with roller or brush;
• coated with a special installation.

Simultaneously spraying with an aqueous solution of coagulant, hydrated calcium chloride (10-12 %), 25 l of water 4 kg of salt — with dual spray, the ratio of coagulant and mastic — 1:8.

Avoid contact with eyes and skin. Store in a dry closed from sun light place at the temperature from +5 to +30° C. shelf Life — 6 months.

Mastic adhesive TECHNONICOL 27 ↑

Ingredients ↑

The ingredients of the mastic are bitumen oil, filler, organic solvent.

The material is used for fixing polystyrene thermopla to concrete, metal and wooden surfaces, bitumen and bitumen-polymer waterproofing.

Methods of application:

• spread the four corners and the Central part thermoplay side gluing;
• strips with a width of at least 40 mm, at a frequency of no less than 4/m^Two;
• drops 50-80 grams of the material at each frequency, 10pcs/m^Two.

Specifications and storage ↑

1. adhesion to concrete and metal surface — 0.1 MPa;
2. the resistance to displacement of the bonding — 0.1 kN/m;
3. non-volatile substances — 75-80 %;
4. temperature resistance — 90° C;
5. the consumption of the material is 0.5-1 kg/m^Two.
6. Store in a dry, well-ventilated closed from sunlight. Avoid contact with eyes and skin.

TECHNONICOL 45, butyl rubber sealant ↑

Viscous material based on butyl rubber with fillers, technological additives and organic solvent, grey or white.

The purpose ↑

• sealing joints in concrete, reinforced concrete and metal constructions, window and balcony blocks of residential and industrial buildings;
• waterproofing of concrete and reinforced concrete, protection of metal from corrosion.

Specifications ↑

1. material density of 900-1100 kg/m^Three;
2. the rupture strength is 0.2 MPa;
3. stretching at break — 100 %;
4. adhesion to concrete — 0.2 MPa;
5. solids by weight — 50 %;
6. drying up «tack-free» — 60 min.;
7. the temperature of the work — from -20 to +40° C;
8. temperature resistance of finished surfaces — from -45 to +45° C.

Method of application ↑

Before use, the material is well mixed, is applied to the surface with a spatula. For use in the cold sealant is aged in a warm room no less than a day.

Mastic TekhnoNikol 31 ↑

Vodoemulsionnye material on oil bitumen containing synthetic rubber, processing AIDS and mineral fillers, solvent-free. Created coatings have high elasticity, adhesion, heat and moisture resistance.

The purpose ↑

• internal waterproofing of the premises;
• construction mastic and repair of all types of roofs as a single material or in combination with a rolled waterproofing and reinforcement;
• protection of the reinforcing structures in contact with moisture.

Specifications ↑

1. adhesion — 0,45 MPa;
2. conventional strength — 0.5 MPa;
3. elongation at break 700 %;
4. water absorption for 24 hours — 1 %;
5. the proportion of binder with emulsifier — 50-70 %;
6. thermal resistance — 95° C;
7. no cracks when bending on the corner of a radius of curvature of 5 mm at -15° C;
8. consumption:
9. the device mastic roof — 3,8-5,7 kg/m^Two;
10. for waterproofing — 2,5-3,5 kg/m^Two;
11. waterproof in tech. 1 h at a pressure of 0.1 MPa.

Method of application ↑

Mastic is applied with a roller, brush or spray on dry or wet surface, spread the rule. Temperature conditions — from +5 to +40° C.

Keep in a dry, closed from sunlight place at a temperature of +5° C or above, to avoid contact with eyes and skin. Shelf life — 6 months.

Mastic TekhnoNikol 71 ↑

Bitumen-polymer material based on bitumen, technological additives.

Purpose: ↑

• repair the deformed parts of the roof;
• filling a void between the corner and the edge rail
• to eliminate gaps when installing aerators, funnels and rubber cuffs.

Specifications: ↑

Conventional strength — 0.2 MPa;

1. adhesion
2. concrete — 0.8 MPa;
3. with metal — 0.4 MPa;
4. between layers — 0,3 MPa;
5. relative stretching at break — 100 %;
6. resistance to displacement of the bonding — 3 kN/m;
7. the content of nonvolatile substances is 80-90 %;
8. water absorption in tech. 24 hours — 2 %.

• Bitumen mastic for waterproofing of roofs with their hands
• Bitumen mastic for waterproofing of the Foundation with his own hands
• Bituminous cold applied with your hands